-
Interface category
10G Ethernet
-
Number of test ports
6 x 10G
-
Interface options
6 x 10GBASE-SR / LR / ER / T 3) / Direct Attached Cable (DAC) 1)
-
Number of transceiver module cages
6 x SFP+
-
Port statistics (2)
Link state, FCS errors, pause frames, ARP/PING, error injections, training packet
All traffic: RX and TX Mbit/s, packets/s, packets, bytes
Traffic w/o test payload: RX and TX Mbit/s, packets/s, packets, bytes
-
Adjustable Inter Frame Gap (IFG)
Configurable from 16 to 56 bytes, default is 20B (12B IFG + 8B preamble)
-
Transmit line rate adjustment
Ability to adjust the effective line rate by forcing idle gaps equivalent to -1000 ppm (increments of 10 ppm)
-
ARP/PING
Supported (configurable IP and MAC address per port)
-
Field upgradeable
System is fully field upgradeable to product releases (FPGA images and Software)
-
Histogram statistics(2)
Two real-time histograms per port. Each histogram can measure one of RX/TX packet length, IFG, jitter, or latency distribution for all traffic, a specific stream, or a filter.
-
Tx disable
Enable/disable of optical laser or copper link
-
IGMPv2 multicast join/leave
IGMPv2 continuous multicast join, with configurable repeat interval
-
Oscillator characteristics
• Initial Accuracy is 3 ppm
• Frequency drift over 1st year: +/- 3 ppm (over 15 years: +/- 15 ppm)
• Temperature Stability: +/- 20 ppm (Total Stability is +/- 35 ppm)
-
Number of transmit streams per port
256 (wire-speed) Each stream can generate millions of traffic flows through the use of field modifiers.
-
Test payload insertion per stream
Wire-speed packet generation with timestamps, sequence numbers, and data integrity signature optionally inserted into each packet.
-
Stream statistics(2)
TX Mbit/s, packets/s, packets, bytes, FCS error
-
Bandwidth profiles
Burst size and density can be specified. Uniform and bursty bandwidth profile streams can be interleaved
-
Field modifiers
16-bit header field modifiers with inc, dec, or random mode. Each modifier has configurable bit-mask, repetition, min, max, and step parameters. 5 modifiers per stream.
-
Packet length controls
Fixed, random, butterfly, and incrementing packet length distributions. Packet length from 56 to 16384 bytes
-
Packet payloads
Repeated user specified 1 to 18B pattern, an 8-bit incrementing pattern
-
Error generation
Undersize length (56B min) and oversize length (16384 max.) packet lengths, injection of sequence, misorder, payload integrity, and FCS errors
-
TX packet header support and RX autodecodes
Ethernet, Ethernet II, VLAN, ARP, IPv4, IPv6, UDP, TCP, LLC, SNAP, GTP, ICMP, RTP, RTCP, STP, MPLS, PBB, or fully specified by user
-
Pause Frames
Responds to incoming pause PFC (Priority-based Flow Control) frames
-
Packet scheduling modes
– Normal (stream interleaved mode): Standard scheduling mode, precise rates, minor variation in packet inter-frame gap.
– Strict Uniform: New scheduling mode, with 100% uniform packet inter-frame gap, minor deviation from configured rates.
– Sequential packet scheduling (sequential stream scheduling): Streams are scheduled continuously in sequential order, with configurable number of packets per stream.
– Burst: Packets per stream are organized in bursts. Bursts from active streams form a burst group. The user specifies time from start of one burst group till start of next burst group.
-
Number of traceable Rx streams per port
2016 (wire-speed)
-
Automatic detection of test payload for received packets
Real-time reporting of statistics and latency, loss, payload integrity, sequence error, and misorder error checking
-
Jitter measurement
Jitter (Packet Delay Variation) measurements compliant to MEF10 standard with 8 ns accuracy. Jitter can be measured on up to 32 streams.
-
Stream statistics(2)
– RX Mbit/s, packets/s, packets, bytes.
– Loss, payload integrity errors, sequence errors, misorder errors
– Min latency, max latency, average latency
– Min jitter, max jitter, average jitter
-
Latency measurements accuracy
±8 ns (opto/elec).
-
Latency measurement resolution
8 ns (Latency measurements can calibrate and remove latency from transceiver modules)
-
Number of filters:
– 6 x 64-bit user-definable match-term patterns with mask, and offset
– 6 x frame length comparator terms (longer, shorter)
– 6 x user-defined filters expressed from AND/OR’ing of the match and length terms.
-
Filter statistics(2)
Per filter: RX Mbit/s, packets/s, packets, bytes.
DataSheet
Support Area
Wire-speed 6-port 10G L2-3 test module
